[Kwintv] Hauppauge WinTV Go-Plus and Fedora Core 3

[George Fragos]

Card=10 should be correct for WinTV-GO, works with mine.  I suggest
you try setting the tuner =44, also works for me.


On Wed, 16 Feb 2005 07:52:25 -0500, William Garber
<garberw at optonline.net> wrote:
> 
> 
> garberw at theta> dmesg | grep bttv
> bttv: driver version 0.9.15 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> bttv: Bt8xx card found (0).
> bttv0: Bt878 (rev 17) at 0000:06:03.0, irq: 185, latency: 32, mmio:
> 0xdfefe000bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID
> is 0070:13eb
> bttv0: using: Hauppauge (bt878) [card=10,autodetected]
> bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
> bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
> bttv0: Hauppauge eeprom: model=29440, tuner=? (-1), radio=no
> bttv0: using tuner=-1
> bttv0: i2c: checking for MSP34xx @ 0x80... not found
> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> bttv0: i2c: checking for TDA9887 @ 0x86... not found
> bttv0: registered device video0
> bttv0: registered device vbi0
> bttv0: PLL: 28636363 => 35468950 .. ok
> garberw at theta>
> root at theta### cat /etc/modprobe.conf
> alias eth0 e100
> alias scsi_hostadapter 3w-xxxx
> alias scsi_hostadapter1 ata_piix
> alias snd-card-0 snd-emu10k1
> options snd-card-0 index=0
> install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1
> && /usr/sbin/alsactl restore >/dev/null 2>&1 || :
> remove snd-emu10k1 { /usr/sbin/alsactl store >/dev/null 2>&1
> || : ; }; /sbin/modprobe -r --ignore-remove snd-emu10k1
> alias char-major-81 bttv
> alias usb-controller ehci-hcd
> alias usb-controller1 uhci-hcd
> alias char-major-195* nvidia
> root at theta###
> 
> 
> On Tue, 2005-02-15 at 22:01 -0500, William Garber wrote:
> > I can't get it to work.
> > Says tuner = -1
> > Tried setting tuner to 2 with
> > rmmod bttv
> > depmod bttv tuner=2
> > sets tuner but still no tv.
> > I think the chip is:
> > Conexant Fusion 878A
> >
> > kdetv shows no plugin for the vbi decoder.
> > There are no "available station detection methods"
> > in the channel wizard.
> >
> > Is the card=10 setting ok?
> >
> > Kudzu set up the card.
> > What should the permissions be on
> > /dev/video0
> >
> > I tried running kdetv as root and as user.
> >
> > tvtime also shows no signal, but I had
> > it working at one time, only got one channel.
> >
> >
> >
> >
> > _______________________________________________
> > kwintv mailing list
> > kwintv at kde.org
> > https://mail.kde.org/mailman/listinfo/kwintv
> 
> _______________________________________________
> kwintv mailing list
> kwintv at kde.org
> https://mail.kde.org/mailman/listinfo/kwintv
> 


-- 
____________
George Fragos
fragos at gmail.com
gfragos at comcast.net
73 East Swift Ave.
Fresno CA 93704