CPP Persistant Class Store crashes KDevelop 3

[Rene Schallner]

And I have found out a bit more:

As I have mentioned, the SIG32 seems  not to be the real problem.

Now when I gdb kdevelop and load a project that has a .pcs file then I
get SIG32 as usual but that one doesn't harm. After "continue" the
source files are loaded, etc, and:

Program received signal SIGSEGV, Segmentation fault.
0x40c4d41e in ?? () from /usr/lib/libkdecore.so.4
(gdb) bt
#0  0x40c4d41e in ?? () from /usr/lib/libkdecore.so.4
(gdb) quit

So above we see the difference to the successful run from my previous
email. 

	-Rene

On Mon, 2003-12-08 at 03:33, Rene Schallner wrote:
> Hi,
> 
> Thanks for your reply. That will keep me busy for a while ... 
> 
> I will enumerate the infos for easy future referencing if you don't
> mind.
> 
> 1.
> Your assumption is correct. Everytime I create a project I can work with
> it up to the point where I load it (or another one previously created) 
> again. However, on the other hand I can successfully load the kdevelop
> project for kdevelop itself (which came with the snapshot) without
> errors. Any other projects (my self created ones) I can only open after
> removal of the .pcs file.
> 
> 2. 
> I do NOT have an SMP machine but my kernel is SMP enabled.
> I guess because of my vast amount of 1GB RAM the Mandrake installer
> chose to install the so called "Enterprise" kernel which supports SMP
> and lots of memory. 
> 
> uname -a
> Linux megavaio.local.net 2.4.22-21mdkenterprise #1 SMP Fri Oct 24
> 19:48:37 MDT 2003 i686 unknown unknown GNU/Linux
> 
> 
> 3. 
> Re Backtrace: I haven't compiled a debug version yet since I didn't know
> I'd be writing this now :-) and I didn't know the performance impact.
> Compiling took about an hour so please tell me if my info would be more
> useful if I ran a debug compile. It could well be that the info below is
> "enough" for spotting what's going on and debug would only show more
> details...
> 
> For the moment, this is my backtrace of an unsuccessful attempt to load
> a project (with a .pcs file present):
> 
> 0x41569686 in waitpid () from /lib/i686/libpthread.so.0
> #0  0x41569686 in waitpid () from /lib/i686/libpthread.so.0
> #1  0x40c4cfda in KCrash::defaultCrashHandler(int) ()
>    from /usr/lib/libkdecore.so.4
> #2  0x416d4ca8 in __libc_sigaction () from /lib/i686/libc.so.6
> 
> 
> 4.
> KDevelop appears to finish well after a successful start. That is: no
> core is dumped and the Crash Handler doesn't pop up.
> I followed your advice and ran kdevelop in gdb to see whether kdevelop
> would finish well after a successful start.
> This is what I got when loading the project:
> 
> Program received signal SIG32, Real-time event 32.
> 0x41565714 in pthread_getconcurrency () from /lib/i686/libpthread.so.0
> (gdb) bt
> 0x41569686 in waitpid () from /lib/i686/libpthread.so.0
> #0  0x41569686 in waitpid () from /lib/i686/libpthread.so.0
> #1  0x40c4cfda in KCrash::defaultCrashHandler(int) ()
>    from /usr/lib/libkdecore.so.4
> #2  0x416d4ca8 in __libc_sigaction () from /lib/i686/libc.so.6
> 
> Please note: I have repeated and verified this 3 times: When not running
> in gdb, the project (with .pcs file deleted) loads successfully. When
> running in gdb it doesn't do so anymore. 
> The time the signal gets received is immediately after all documents
> have been loaded, where I would normally see "Updating..." when the
> persistant class store gets recreated.
> 
> My personal opinion when I see this and because you asked about SMP:
> There might be some synchronization problem (in the persistant class
> store stuff?) and running under gdb modifies the timing (things go more
> slowly) and that's why the crash shows up in gdb when it wouldn't
> otherwise...?
> 
> One more thing. I have now booted into the "standard" linux kernel, not
> the enterprise kernel:
> 
> [rene at megavaio rene]$ uname -a
> Linux megavaio.local.net 2.4.22-10mdk #1 Thu Sep 18 12:30:58 CEST 2003
> i686 unknown unknown GNU/Linux
> 
> And that did not help. Even with the non-SMP-enabled kernel I get the
> same error when trying to load a project w/o removing the .pcs file.
> 
> best regards,
> 	Rene
> 
> On Sun, 2003-12-07 at 19:10, Alexander Dymo wrote: 
> > I understand that you have .pcs loading problems each time you create a
> > project. Is it correct?
> > Some additional questions to clarify situation:
> > do you have smp machine?
> > can you send us the backtrace?
> > does kdevelop finish well (are there crashes at exit after a 
> > _successfull_ start)?
> > 
> > Please check third situation. Run kdevelop in gdb (when all .pcs files
> > are deleted):
> > gdb kdevelop
> > run
> > bt
> 
> 
> _______________________________________________
> Kdevelop-devel mailing list
> Kdevelop-devel at barney.cs.uni-potsdam.de
> http://barney.cs.uni-potsdam.de/mailman/listinfo/kdevelop-devel
>