<br>
<br><tt><font size=2>roland <roland@cat.be> wrote on 10/11/2009 13:23:08:<br>
<br>
etc etc<br>
> ><br>
> I am the only one that is connected to that server (Compaq-HP ML350
6GB <br>
> RAM)<br>
> When I work locally, nomachine will start from an acer travelmate
3000 <br>
> centrino processor. In this case there are no problems, except that
work </font></tt>
<br>
<br>
<br>
<br><tt><font size=2>Server works, FreeNX works, account works. Good</font></tt>
<br>
<br>
<br>
<br><tt><font size=2>> is done on a 21 inch Display, (Nomachine full
screen) and experienced as <br>
> slower than Vnc.<br>
</font></tt>
<br>
<br><tt><font size=2>VNC doesn't have to have the time lag for compression
so on a fast LAN with </font></tt>
<br><tt><font size=2>no latency issues . . .</font></tt>
<br>
<br>
<br><tt><font size=2>> <br>
> When I work remote, nomachine starts from a netbook Samsung Atom processor<br>
> <br>
</font></tt>
<br><tt><font size=2>Should work, though xp is now so slow, memory hungry
and bloated that it</font></tt>
<br><tt><font size=2>probably won't go as well as Linux on a netbook.</font></tt>
<br>
<br><tt><font size=2>Anyone would think M$ wanted to push us onto Vista
or W7.</font></tt>
<br>
<br>
<br><tt><font size=2>> In the latter case, there is no problem with
login. It happens, as I <br>
> mentioned before, after some little on-line time, few minutes, sometimes,
<br>
> exceptionally, much longer.<br>
</font></tt>
<br><tt><font size=2>The timeout due to not completeing takes about 3-4
mins AFAIK.</font></tt>
<br>
<br><tt><font size=2>If it reaches 10 mins then it's probably something
else.</font></tt>
<br>
<br>
<br><tt><font size=2>> Remote I work via a DSL-stick (HSPDA) or from
a Wifi, depending upon where <br>
> I am, i.o.w. everywhere in Belgium, Germany or France.<br>
> <br>
</font></tt>
<br><tt><font size=2>HSPDA sticks often end up working a lot slower then
you would hope, not always </font></tt>
<br><tt><font size=2>due to 3G issues, but the IP net behind them.</font></tt>
<br>
<br><tt><font size=2>Its worth keeping an eye on what speeds you
are getting. One week it can</font></tt>
<br><tt><font size=2>be OK another week it seems OK browsing, but is slow
and may have high </font></tt>
<br><tt><font size=2>packet loss.</font></tt>
<br>
<br><tt><font size=2>Dos this happen all the time on a variety of wifi
points too ??</font></tt>
<br>
<br><tt><font size=2>> I hope this is enough info.<br>
> </font></tt>
<br>
<br><tt><font size=2>> I forgot to write below, that after this little
time, the session is not <br>
> disconnected, but only input-locked.<br>
</font></tt>
<br><tt><font size=2>?????</font></tt>
<br>
<br><tt><font size=2>Do you mean that if you run something with output
to screen that you can </font></tt>
<br><tt><font size=2>see the output continuing to move, but can't control
the session ??</font></tt>
<br>
<br><tt><font size=2>When you re-connect to the running session, does it
time out again or work </font></tt>
<br><tt><font size=2>continually after that ??</font></tt>
<br>
<br><tt><font size=2>Are you trying to connect remote smb drives or printers
etc??</font></tt>
<br>
<br><tt><font size=2>Are you doing other work at the same time, email clients
etc</font></tt>
<br>
<br><tt><font size=2>> But I have the impression that, even after locking,
some keystrokes are <br>
> accepted. p.e. when I do Ctrl-Alt-T, nothing happens.<br>
> When coming back, after Ctrl-Alt-shift-Esc, the session showes the
message <br>
> that Ctrl-Alt-T should show, i.e. the option cancel session.<br>
></font></tt>
<br>
<br><tt><font size=2>I would guess networking issues based on what you
say.</font></tt>
<br>
<br><tt><font size=2>BUT</font></tt>
<br>
<br><tt><font size=2>you haven't told us what hapens when you put the Samsung
netbook on the LAN</font></tt>
<br><tt><font size=2>and try it locally !!</font></tt>
<br>
<br>
<br><tt><font size=2><br>
> Thanks for replying<br>
> <br>
> Roland<br>
> ________________________________________________________________<br>
> Were you helped on this list with your FreeNX
problem?<br>
> Then please write up the solution in the FreeNX Wiki/FAQ:<br>
> <br>
> </font></tt><a href="http://openfacts2.berlios.de/wikien/index.php/BerliosProject:FreeNX_-_FAQ"><tt><font size=2>http://openfacts2.berlios.de/wikien/index.php/BerliosProject:FreeNX_-_FAQ</font></tt></a><tt><font size=2><br>
> <br>
> Don't forget to check the NX Knowledge
Base:<br>
> </font></tt><a href=http://www.nomachine.com/kb/><tt><font size=2>http://www.nomachine.com/kb/</font></tt></a><tt><font size=2>
<br>
> <br>
> ________________________________________________________________<br>
> FreeNX-kNX mailing list --- FreeNX-kNX@kde.org<br>
> </font></tt><a href="https://mail.kde.org/mailman/listinfo/freenx-knx"><tt><font size=2>https://mail.kde.org/mailman/listinfo/freenx-knx</font></tt></a><tt><font size=2><br>
> ________________________________________________________________<br>
</font></tt>